产品名称

Name

内径

Intermal diameter (mm)

性能及用途

Performance and use

备注

Remark

输水胶管

Rubber hoses for water transportation

10-25

输送60℃以下的生活用水、工业用水的橡胶软管Rubber hoses for transportation of water with temperature no more  than 60℃.

压缩空气用胶管

Rubber hoses for compressed air

6-25

工业温度在-20℃～+45℃输送工作压力在2.5MPa以下的工业用压缩空气采矿和建筑工程用压缩空气。Compressed air for mining or construction industry with working  temperature range -20℃—+45℃, and working pressure no more than 2.5MPa.

蒸气胶管

Steam hose

6-76

输送170℃以下的饱和蒸汽或过热水，工作压力为蒸汽0.35MPa，热水0.8MPa。Convey saturated steam or hot water under 170℃, working pressure: steam, 0.35Mpa, hot water, 0.8Mpa.

输吸油胶管

Oil conveying and sucking hose

6-152

常温下吸送汽油、机油、润滑油及其它矿物油。工作压力为0.5-1.2MPa。At normal  temperature, suck and convey petroleum, machine oil, lubrication and other  mineral oil.Working temperature, 0.5-1.2Mpa. 

也可采用外铠装结构External armored structure can also be used

输吸食品胶管

Food conveying and sucking hose

16-152

吸引奶类、酒类、食用油类及液体饮料。工作压力为0.5-0.8MPa。 Suck milk, wine,  eatable oil, and liquid beverage.Working pressure, 0.5-0.8Mpa.

输酸、碱胶管

Acid, alkali co-nveying hose

19-203

常温下输送稀酸、碱溶液。工作压力为0.5-0.7MPa。

At normal temperature, convey thick acid,  alkali solution. Working pressure, 0.5-0.7Mpa.

输送浓酸时内胶层可采用丁基胶，布层可采用玻璃纤维。When thick acid conveyed, butyl rubber can be used as the inner  layer, and fabric glass can be used as the fabric layer.

耐磨喷砂胶管

Abrasive sand blast

19-76

风压喷砂用软管，工作压力为0.6MPa。 Wind pressure  sand spraying hose, working pressure, 0.6Mpa.

水泥罐车用管也可按此生产 Hose for the cement tank car can be produced like this.

水箱弯管

Tank elbow

25-102

机车水箱输水用。Locomotive tank water piping.

尼纶线缠绕吹氧胶管

Nylon thread  spiral oxygen blowing hose

51-127

纯氧顶吹转炉用挠性连接管，工作压力为1.5MPa，

也可采用钢丝编织扣压式，工作压力可达8MPa。

Used as the joint hose of pure oxygen  top-blown converter, working pressure, 1.5Mpa; steel wire braided extruded  type can also be used, working pressure 8Mpa.

两端硫化金属法兰，外有石棉保护层。Vulcanized metal flanges on both ends, protected by external  asbestos layer

排(吸)泥胶管

Mud pumping hose

196-900

挖泥船排（吸）泥沙用，工作压力为0.4-0.5MPa。

Used for mud piping of dredge, working  pressure 0.4-0.5Mpa.

根据设计需要可带有法兰接头Flange adapter can be accompanied according the need of design.

制孔胶管

Hole making hose

25，32，40

桥梁公路等工程建筑制孔用，承受拉力为1.5-2.30kg/根。Used for hole  making of bridge and highway construction, bearing tensile force,  1.5-2.30kg/pipe.

外层胶具有良好的撕拉性能External rubber layer with high tearing strength.